Quick Answer:
Choose VFFS film by matching the product, shelf-life needs, film structure, machine settings, and target production speed—not by polymer name or thickness alone.
- Start with product protection: Define oxygen, moisture, light, grease, puncture, and shelf-life requirements.
- Choose the complete film structure: Compare monoweb, laminated, coextruded, and recyclable options based on performance, not material name alone.
- Check VFFS runnability: Seal window, hot tack, COF, stiffness, curl, gauge, puncture resistance, and static behavior all affect machine performance.
- Match the actual machine: Confirm web width, repeat length, fin or lap seal, registration marks, reel size, unwind direction, and intermittent or continuous motion.
- Do not assume thicker or lower-COF film is better: Mechanical strength and web handling depend on the full structure and machine setup.
- Run a real production trial: Validate target speed, seal quality, tracking, registration, rejects, and restart performance with the actual product.
- Approve an operating window, not one perfect setting: The best VFFS film should remain stable across realistic production variation.

Choosing film for a vertical form fill seal machine is not simply a matter of selecting PE, PET, or a certain thickness. The film must protect the product, move predictably through the machine, form the required bag, and create reliable seals at production speed.
The best selection process starts with the product and finished package, converts those needs into measurable film specifications, and ends with validation on the actual VFFS machine.
What Does a VFFS Film Need to Do?

A VFFS machine converts flat rollstock into a package through forming, filling, and sealing. Each stage places different demands on the film.
| VFFS Stage | What the Film Must Do | Key Properties |
|---|---|---|
| Form | Unwind, track, pass over the forming collar, and wrap around the tube consistently | Stiffness, dimensional stability, COF, curl control |
| Fill | Withstand the product load without tearing, puncturing, or distorting | Toughness, puncture resistance, tear behavior |
| Seal | Form repeatable longitudinal and cross seals within the machine cycle | Seal window, hot tack, seal strength, contamination tolerance |
These properties must work together. Excellent barrier performance has limited value if the web will not track consistently, just as smooth machine handling cannot compensate for weak package protection.
VFFS machine guidance also identifies smoothness, dimensional stability, low-temperature sealability, hot tack, and antistatic performance as important film characteristics. [8]
Start With the Product and Required Shelf Life

Do not begin by asking which polymer to buy. First define what the package must protect the product from.
| Product or Packaging Risk | Film Requirement | Useful Specification |
|---|---|---|
| Oxidation | Oxygen barrier | OTR |
| Moisture gain or loss | Moisture barrier | WVTR |
| Aroma loss | Gas and aroma retention | Barrier structure |
| Light-sensitive product | Light protection | Opaque, metallized, or suitable barrier layer |
| Sharp or hard product | Mechanical protection | Puncture and tear resistance |
| Powder or fine particles | Reliable sealing with product near the seal | Contamination-tolerant sealing performance |
| Frozen product | Low-temperature toughness | Cold-impact and flex performance |
| Oily or greasy product | Product-contact resistance | Compatible sealant and barrier structure |
OTR, or oxygen transmission rate, measures oxygen passing through a film under defined test conditions. ASTM D3985-24 covers OTR measurement for plastic films, laminates, coextrusions, and coated structures and notes that OTR is an important—but not the only—indicator of barrier-package protection. [1]
WVTR measures water-vapor transmission. ASTM F1249-25 covers WVTR measurement for plastic film and sheeting and identifies WVTR as an important packaging property that can relate to shelf life and product stability. [2]
The required barrier values should therefore come from the product’s shelf-life target and expected storage conditions rather than from a generic assumption about its category.
Two products running on the same VFFS machine may need very different films if one is moisture-sensitive while the other is primarily vulnerable to oxidation.
Define the required performance first. Build the film structure second.
Choose the Film Structure, Not Just a Polymer Name
VFFS films can use monoweb, laminated, coextruded, or other engineered structures. The buyer should evaluate what each layer contributes instead of treating one polymer name as the complete specification.
Monoweb Films
A monoweb uses one film web rather than bonding separately produced webs through lamination.
It can simplify construction and, in suitable designs, support recycling goals. The challenge is that the same web must still provide the required sealing, mechanical, printing, and barrier performance.
Laminated Films

Lamination allows different layers to perform different jobs.
A typical structure may combine:
- an outer layer for printing, stiffness, or heat resistance;
- a barrier or strength layer;
- an inner product-contact layer for sealing.
Common materials include PET, OPP/BOPP, PE, LLDPE, CPP, EVOH, metallized films, and functional coatings.
Coextruded Films

Coextrusion forms multiple polymer layers during the film-making process rather than bonding separately produced webs afterward.
This can combine properties such as sealing, toughness, stiffness, and barrier performance in one structure.
The important purchasing question is not whether a film is laminated or coextruded by itself. It is whether the complete structure meets the package and machine requirements.
| Material or Layer | Common Role | Buyer Should Check |
|---|---|---|
| PET | Stiffness, printing surface, heat resistance | Formability, laminate construction |
| OPP/BOPP | Stiffness, clarity, moisture resistance | COF, seal arrangement, print compatibility |
| PE/LLDPE | Sealability, toughness, product-contact layer | Seal window, hot tack, stiffness |
| CPP | Sealability and heat performance | Seal range and mechanical needs |
| EVOH | Oxygen barrier | Humidity exposure and structure design |
| Metallized layer | Light and barrier performance | Flex durability and recycling implications |
| Functional coating | Barrier or surface modification | Durability, sealing, recycling compatibility |
Recyclable and Lower-Material Structures
Recyclability should be treated as another performance requirement rather than a replacement for package performance.
Mono-PE and mono-PP structures can improve alignment with compatible flexible-plastic recycling streams, but the complete structure still matters. RecyClass continued updating its PE and PP flexible-packaging Design for Recycling guidelines in 2026, including criteria involving printing inks and other film components. [3]
Changing from a conventional laminate to another structure can alter stiffness, friction, sealing behavior, heat resistance, and barrier performance.
The practical question is:
Can the new structure protect the product and run reliably on the target VFFS machine?
A substantial film-structure change should be validated again under production conditions.
The Film Properties That Control VFFS Runnability

Film composition tells you what the material is made from. Runnability determines whether the machine can convert it efficiently.
Seal Window and Seal Initiation
VFFS heat sealing depends on temperature, pressure, and dwell time.
The sealant must form an acceptable seal within the available machine cycle while tolerating normal process variation without sticking, distorting, or losing seal integrity.
ASTM F2029-16(2021) provides laboratory practices for producing heat seals used to study flexible-material heat sealability. It also states that the resulting relationships are starting guidance and do not replace validation on commercial production equipment. [4]
For production, a practical operating range is more valuable than one narrow optimum temperature.
A broader usable seal window gives the process more tolerance for normal temperature, speed, and material variation.
Hot Tack
Hot tack is the strength of a heat seal immediately after sealing and before it cools.
This is particularly relevant to form-fill operations because newly formed seals can experience product load while still hot. ASTM F1921/F1921M-12(2023) specifically measures hot seal strength and notes that insufficient resistance at this stage can cause package failure during the packaging process. [5]
Hot tack and final seal strength are therefore different performance measures.
A film may develop strong seals after cooling yet perform poorly on a fast VFFS line if the fresh seal cannot withstand the immediate load.
Coefficient of Friction
Coefficient of friction, or COF, affects how the film interacts with rollers, forming surfaces, pull belts, and other film surfaces.
ASTM D1894-24 measures static and kinetic COF for plastic film and states that these frictional properties relate to slip behavior important in packaging applications. [6]
Excessive friction can contribute to drag and unstable web movement. Very low friction is not automatically better either; on some machines, insufficient traction can make film pulling or web control more difficult.
The useful specification is therefore a machine-compatible COF range, not the lowest possible number.
Stiffness, Curl, and Dimensional Stability
The film needs enough stiffness for controlled web handling while remaining flexible enough to form around the collar and tube.
Curl, stretch, or dimensional variation can contribute to:
- registration drift;
- wrinkles;
- changing bag length;
- unstable tracking;
- inconsistent package shape.
These properties should be evaluated with the film moving through the machine, not only as a flat sample.
Gauge, Puncture, and Tear Resistance
Film thickness matters, but gauge alone does not define strength.
Polymer selection, orientation, layer construction, lamination, and sealant design can all change mechanical performance. A well-engineered thinner structure can therefore outperform a thicker film for a specific application.
Products with sharp edges, hard particles, frozen pieces, or heavy fill weights require particular attention to puncture and tear performance.
Select gauge from the mechanical requirement rather than simply specifying the thickest material the machine can run.
Static and Powder Handling
Powders and fine granules can create additional film-handling and sealing problems.
Static can encourage lightweight product to cling to surfaces, while product reaching the cross-seal area can reduce sealing consistency.
For these applications, antistatic performance, filling control, dust management, and sealing conditions should be considered together. VFFS machine guidance specifically identifies antistatic film as relevant to powder and granular products. [8]
Match the Film to the VFFS Machine and Bag Format

A good film specification must match the actual machine, forming set, sealing system, registration sensor, and finished package.
Intermittent vs Continuous Motion
Intermittent-motion machines stop the web during part of the packaging cycle, while continuous-motion systems keep the film moving.
This changes how sealing time, web control, and speed interact. Continuous-motion applications can place tighter demands on fast, repeatable sealing and hot-tack performance because sealing takes place while production remains in motion.
The film should therefore be qualified on the motion type and target speed for which it will actually be used.
Fin Seal vs Lap Seal
The longitudinal seal geometry also affects film compatibility.
A fin seal normally joins the two sealant surfaces. A lap seal can require one side of the structure to seal to the opposite surface.
A film designed only for sealant-to-sealant bonding may therefore be unsuitable for a package that requires a different seal interface.
Define the back-seal configuration before the final structure is approved.
Web Width and Repeat Length
Web width must match the forming set and package design, including the longitudinal seal allowance and any gusset requirements.
Print repeat must align with bag length, seal areas, registration marks, artwork, and cut position.
Neither value should be estimated from the finished bag dimensions alone. Use the approved forming-set and package drawings when releasing the film specification.
Print Registration and Eye Marks
Printed film requires a repeatable reference that allows the machine to position artwork, seals, and cuts correctly.
Specify:
- eye-mark size and position;
- contrast;
- sensor-facing side;
- print repeat;
- cut position;
- registration tolerance.
Transparent, metallic, reflective, or heavily printed webs may also require confirmation that the machine’s registration sensor can detect the mark reliably.
Reel Specification
Roll construction is part of machine compatibility.
Confirm:
- core inside diameter;
- reel width;
- maximum outside diameter;
- maximum reel weight;
- unwind direction;
- print orientation;
- sealant orientation;
- splice requirements;
- acceptable roll-edge condition.
A film can have the correct chemistry and dimensions yet still be unusable if the roll is wound or oriented incorrectly for the machine.
How to Choose VFFS Film Step by Step

Use the selection process to move from product requirements to an approved technical specification.
- Define the product. Identify product condition, fill temperature, weight, sharp edges, oil or moisture content, powder behavior, and seal-contamination risks.
- Set shelf-life requirements. Determine whether oxygen, moisture, light, aroma, grease, or gas-flush performance needs to be controlled.
- Define the finished package. Confirm bag style, dimensions, gussets, fill weight, longitudinal seal, cross-seal area, and required headspace.
- Document the machine. Record the VFFS model, motion type, forming set, sealing system, pull system, registration sensor, and reel limits.
- Set runnability targets. Define production speed and the required sealing, COF, hot-tack, stiffness, and mechanical performance.
- Complete the roll and artwork specification. Confirm web width, repeat, eye mark, cut position, unwind direction, core, reel OD, and print orientation.
- Validate the production structure. Run the actual film with the intended product and package at representative production conditions.
The final specification should give the film converter and machine team one common technical reference.
| Specification Field | What to Record |
|---|---|
| Product | Type and relevant physical characteristics |
| Fill quantity | Normal range and maximum load |
| Shelf life | Required period and storage conditions |
| Film structure | Approved layer sequence or construction |
| Total gauge | Nominal thickness and tolerance |
| Barrier | Required OTR, WVTR, or other barrier target |
| Seal performance | Usable seal range, hot tack, final seal requirement |
| COF | Required surface, range, and test basis |
| Web width | Approved machine value |
| Print repeat | Approved repeat and tolerance |
| Eye mark | Size, position, contrast, sensor side |
| Reel | Core ID, OD, weight, unwind direction |
| Target speed | Required good packages per minute or hour |
| Finished bag | Approved drawing and dimensions |
How to Run a VFFS Film Trial Before Approval
A film trial should prove a usable production window—not merely show that the machine can make several acceptable bags at one setting.
Run enough film to evaluate:
- startup and sustained production;
- target operating speed;
- longitudinal and cross-seal quality;
- hot-tack performance;
- final seal strength and package integrity;
- registration and cut position;
- bag dimensions;
- tracking and wrinkling;
- stretching, curl, or film breaks;
- product contamination in the seal area;
- stops and restarts;
- relevant reel splices or reel changes;
- scrap and reject rate;
- good packages produced per hour.
ASTM F88/F88M-23 measures the force required to separate seals in flexible barrier materials and can be used to assess final seal strength. [7] Hot-tack testing under ASTM F1921/F1921M evaluates the seal before it cools. [5]
The distinction matters when comparing films.
For example, one film may run acceptably only within a narrow jaw-temperature range, while another remains stable across a broader range at the same output. Even if both eventually achieve acceptable cooled seal strength, the second film can provide a more forgiving production process.
The exact temperature range is application-specific.
A good trial proves an operating window, not one perfect machine setting.
Common VFFS Film Selection Mistakes

- Choosing by polymer name alone: Define barrier, sealing, mechanical, and machine requirements first.
- Choosing gauge without mechanical testing: Thickness does not define puncture, tear, or toughness by itself.
- Assuming lower COF is always better: The film still needs suitable traction and controlled web movement.
- Checking final seal strength but ignoring hot tack: A cooled seal can pass while the fresh seal fails during filling.
- Approving film after a short low-speed trial: Qualify the film at realistic speed and process conditions.
- Changing film structure without rerunning trials: New structures can change friction, stiffness, sealing, heat resistance, and barrier performance.
FAQs About Choosing Film for VFFS Machines
What film is best for VFFS machines?
There is no single best VFFS film. The correct structure protects the product, forms consistently, tracks reliably, seals within the available machine cycle, and meets the required shelf life and package strength.
What thickness should VFFS film be?
There is no universal VFFS film thickness. Gauge depends on structure, bag size, fill weight, puncture risk, stiffness, barrier needs, and machine handling. Specify the required performance and confirm the gauge through testing.
What COF is best for VFFS film?
There is no universal COF target for every machine. The suitable range depends on film surfaces, forming components, pull system, tension control, and speed. Specify the tested surface and verify the result on the actual VFFS machine.
Why does VFFS film wrinkle or track poorly?
Common causes include unsuitable friction, uneven tension, curl, dimensional instability, poor roll edges, machine misalignment, or an incorrect forming setup. Check the film and web-handling system together rather than treating registration alone as the problem.
What is hot tack in VFFS packaging?
Hot tack is the strength of a heat seal before it cools. It matters because the newly formed bottom seal may receive the product load almost immediately. A film can have acceptable cooled seal strength but insufficient hot tack for the packaging cycle. [5]
Can recyclable mono-material film run on existing VFFS machines?
Yes, many mono-material structures can run on existing VFFS equipment, but compatibility should be validated. Changes in structure can affect sealing, friction, stiffness, heat resistance, barrier performance, and the machine’s stable operating speed.
Conclusion
The right VFFS film is not simply the cheapest roll or the structure with the highest barrier rating. It is the film that protects the product, seals reliably, and runs consistently at the required production speed.
Start with the product and shelf-life requirements, translate them into measurable film and roll specifications, and confirm the final structure on the actual machine.
Treat the product, film, bag, and VFFS machine as one system. If you are evaluating a new film or troubleshooting an existing setup, share your product, bag dimensions, current film structure, and target speed with our team so we can help assess film compatibility and recommend a more reliable VFFS packaging solution.
References
[1]. ASTM International, ASTM D3985-24 — Standard Test Method for Oxygen Gas Transmission Rate Through Plastic Film and Sheeting Using a Coulometric Sensor.
[2]. ASTM International, ASTM F1249-25 — Standard Test Method for Water Vapor Transmission Rate Through Plastic Film and Sheeting Using a Modulated Infrared Sensor.
[3]. RecyClass, Design for Recycling Guidelines, updated March 2026.
[4]. ASTM International, ASTM F2029-16(2021) — Standard Practices for Making Laboratory Heat Seals for Determination of Heat Sealability of Flexible Barrier Materials as Measured by Seal Strength.
[5]. ASTM International, ASTM F1921/F1921M-12(2023) — Standard Test Methods for Hot Seal Strength (Hot Tack) of Thermoplastic Polymers and Blends Comprising the Sealing Surfaces of Flexible Webs.
[6]. ASTM International, ASTM D1894-24 — Standard Test Method for Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting.
[7]. ASTM International, ASTM F88/F88M-23 — Standard Test Method for Seal Strength of Flexible Barrier Materials.
[8]. Tokyo Automatic Machinery Works, Required Film Function for VFFS Machine.


